The Intelligent House, Building Automation eHouse RS-485 can be controlled via Cloud eHouse Cloud .
This is another option besides direct access through eHouse for Java , Android (TCP / IP, UDP, SMS, eMail) and web browser.
One control method does not exclude another.
The following project is a comfort installation system (one controller per room) with full access from outside. eHouse RS-485 demo project was discussed in earlier posts:
The installation realizes the complete automation of the building ~ 300m2 (basement, ground floor, top floor) – in the comfort version.
The system is based on eHouse PRO server and eHouse RS-485 controllers for small switchboards (all inputs / outputs from single room goes to room switchboard).
“Working in the cloud” is the synchronization of system data with the Web server and MySQL database.
Advantages of Cloud:
- Can work with any Internet connection without any restrictions
- does not require public access Internet
- Does not require a fixed IP address or DDNS service for the link
- No complicated configuration of NAT Internet Router, sharing and redirection of Ports, Servers, DMZ, etc.
- If you work on the web, it can be controlled from any device with a web browser
Disadvantages of Cloud:
- Higher link load and data transfer
- slower, refresh and delay than direct access (3 to tens of seconds of refresh)
- depends on the stability of the WWW/MySQL server
- loads the WWW/MySQL server and needs a large data transfer for each installation
To reduce disposing of the link and web server/MySQL, the refresh is set to 60 seconds when the client is not connected to the cloud. In case of connection and start up of the system command, the frequency increases (up to several dozen or so seconds) depending on the configuration.
Because it requires a web server, it is a paid service that depends on the amount of data transferred (transfer rate and refresh rate).
At: eHouse RS-485 + Cloud Building Automation is publicly available (without passwords) Centralized demonstration system installation. It is also an eHouse RS-485 under eHouse PRO Server test installation for BMS system integrators to test the system without eHouse hardware.
Because visualizations are in text files, it is easy to edit and change.
EHouse visualizations: Web visualizations – eHouse Building Automation
Creating visualizations: eHouse Building Automation
eHouse One Electronic House – single segment of Decentralized Installation Diagram – distributed home automation
Smart Home , intelligent Building eHouse is a system of electronic home , optimized for the installation of decentralized ( distributed ) .
Continue reading eHouse One Electronic House – single segment installation
eHouse Electronic House – Connecting Decentralized Installation segments
Smart Home , intelligent Building eHouse can be powered from the AC discussed in the post
Continue reading eHouse Electronic House – connecting decentralized segments
eHouse Electronic House – Power Home Automation system
Smart Home , Home Automation eHouse is a low voltage control system of the house .
Proper power supply in electronic circuits is always the most important factor of electronic devices , both analog and digital .
Continue reading eHouse Electronic House – powering home automation DIY
eHouse Smart House – Connecting relay drivers . Mini switchboard – decentralized Installation
Smart Home , intelligent Building , eHouse Home Automation system is a low voltage ( electronics home) , powered with DC voltage of approximately 12V .
Continue reading eHouse Smart House Connecting Relays
Home Automation eHouse Connecting the Demonstration , Evaluation
Smart House , Home Automation eHouse can be tested using the module smart home Demo .
Demonstration module requires +12V power supply computer power supply preferably with a computer , which connect the entire system , using standard PC power connector ( 4Pin ) .
Continue reading eHouse home automation, smart home connection of evaluation/demo board
eHouse Smart House Demo – package Evaluative
Smart Home , home Automation eHouse is relatively advanced system and how each similar system is based on the assumptions of the design selected and supported by over 14 years of experience and development of the system aimed at :
Continue reading eHouse 1 Smart Home Demo/Evaluation
RoomManager – smart home controller
Smart House , intelligent Building eHouse has drivers room RoomManager dedicated control rooms. They are optimized to control one or a group of premises .
Continue reading eHouse RS-485 smart home, intelligent building
RS-485 eHouse Home Automation controller installation RoomManager – do it yourself
Smart Home eHouse RS-485 standalone installation of RoomManager in controlled room .
In this post we will describe the easiest way to connect and install the RoomManager in RS-485 version.
Continue reading eHouse RS-485 smart home – do it yourself installation
eHouse 1 Electronic home mini switchboard self installation
Smart Home “eHouse 1” installation of a single segment of the system and a mini indoor switchboard controlled.
Connecting the controller to the relay outputs , receivers and power supply to the controller.
Continue reading eHouse RS-485 connecting mini switchboard – do it yourself